Electronic Speed Controls

Sort By:  
Spedix employed the use of larger MOSFETs to improve efficiency, increase heat dissipation, and deal with higher current all while maintaining a reasonable size.
$51.99
The GS35 4-1 ESC is a 4-in-1 version of its GS35 ESC series. Capable of the extremely quick DShot 1200 protocol. Spedix is known for quality ESCs and this one is no different, but with the convenience of a 4-in-1
$55.99
Blheli-32 bit 4in1 offering from Spedix. This wonderful 4 in1 esc is Dshot1200 capable and has a 45 amp burst.
$55.99
The Typhoon 4in1 S Racer ESC 4x30A runs BLHELI_S fimrware, supports our ESCLINKER and BLHELIsuit, it offer the best performance in 35x35mm size. incl. Current and voltage measuring.
$49.99
4in1 ESC with 30.5x30.5 mm Mounting holes, supports DSHOT 1200, BLHELI32 firmware.
$59.99
Spedix IS 30 amp 4in1 (Spedix IS30a 4in1)

Features

  • Standard 30.5mm spaced mounting holes
  • The dimensions of the board (except the soldering pads) are 36x36mm, the same as a standard flight controller.
  • The extended soldering pads can be easily soldered in place without disassembling your machine
  • Efficient switching 5V/1.2A BEC output.
  • Uses a more reliable 1.25mm pitch 7 pin Molex connector containing 4 ESC signals, 5V supply and VBAT
  • Additionally there are three set of solder pads. One 5V output, and two at battery voltage level that can be used for video transmitters, accessories or the optional electrolytic capacitor (included)
  • 6.1mm diameter clearance around mounting holes (clearance for spacers without hitting components is a common problem among 4in1 ESCs)

Specifications

  • Size: 36mm x 36mm x 5mm
  • Mounting Holes: 30.5mm x 30.5mm
  • Weight: 10.3 grams (no wires)
  • 30Amp/40Amp Burst
  • 2-4S
  • EFM8BB21 MCU
  • 3 oz copper PCB
  • 5x6mm MOSFETs
  • BLHeli_S firmware
  • Supports Oneshot125, Oneshot42, Multishot, DSHOT600

Includes

  • IS30 4in1 ESC
  • 16 AWG power wires
  • 7 pin connector to bare wires
  • 7 pin connector with servo leads (1x3pin w/BEC, rest single connectors)
  • 25V 330µF Rubycon ZLH electrolytic capacitor, can be used for further voltage spike suppression (general purpose cap, not low ESR)
Spedix employed the use of larger MOSFETs to improve efficiency, increase heat dissipation, and deal with higher current all while maintaining a reasonable size.
$51.99
Spedix GS 35 4in1 (Spedix GS35 4in1)

Specification:

Firmware: BLHeli 32 bit
Input: 2-4 Cell LiPo
Cont./Burest Current: 35A/45A≥10S
Size:37x41x5 mm
Weight:11.8 g(including cables)
Current detection supported

The GS35 4-1 ESC is a 4-in-1 version of its GS35 ESC series. Capable of the extremely quick DShot 1200 protocol. Spedix is known for quality ESCs and this one is no different, but with the convenience of a 4-in-1
$55.99
Spedix GS 35 amp 4in1 (Spedix GS354in1)

Specification:

  • Firmware: BLHeli 32 bit
  • Input: 2-4 Cell LiPo
  • Cont./Burest Current: 35A/45A≥10S
  • Size:37x41x5 mm
  • Weight:11.8 g(including cables)
  • Current detection supported
Blheli-32 bit 4in1 offering from Spedix. This wonderful 4 in1 esc is Dshot1200 capable and has a 45 amp burst.
$55.99
Typhoon 4in1 S Racer ESC 4x30A (Typhoon 4in1 S Racer)

The Typhoon 4in1 S Racer ESC 4x30A runs BLHELI_S fimrware, supports our ESCLINKER and BLHELIsuit, it offer the best performance in 35x35mm size. incl. Current and voltage measuring. 
Works up to 30A each motor.


Features:

  • BB21 MCU, 48Mhz Runs BLHELI_S J_H_xx firmware
  • Supports 3-6S lipo input
  • 4PWM input
  • Current and Voltage output
  • NO BEC
  • Supports oneshot / Multishot / Dshot PWM
  • Only 36x36mm, mount holes 30.5x30.5mm
  • Supports damped light
  • NO External capacitors needed

Different frame will cause different test result with the current, we rated it as the mid-value, in your frame, the current may higher or lower, there is no Guarantee, if you can get same result in your frame.

Package incl.:

  • Typhoon S Racer 4in1 ESC
  • 2x 6pin SH1.0 to 2.54 DuPont Cable (one for PWM input, one for Current output)
The Typhoon 4in1 S Racer ESC 4x30A runs BLHELI_S fimrware, supports our ESCLINKER and BLHELIsuit, it offer the best performance in 35x35mm size. incl. Current and voltage measuring.
$49.99
Typhoon32 4in1 ESC 4x35A v2 (Typhoon32 4in1)

4in1 ESC with 30.5x30.5mm mounting holes, supports DSHOT 1200, BLHELI32 firmware.

On this version, we added more CAPS to reduce power noise.

 

  •  32bit ESC with BLHELI32 firmware
  •  Supports 3-6S lipo input
  •  4PWM input
  •  Voltage output (VBAT)
  •  Supports Oneshot / Multishot / Dshot PWM
  •  Mounting holes 30.5x30.5mm
  •  Supports damped light
  •  NO BEC

Package includes:

1 x 4in1 ESC board

 

NOTE: 

  • This does not include any cables or connectors. Please order separately.
  • Different builds will have different results in terms of current draw. We rated it at the mid-value. We cannot guarantee this board will have the same results on every build.
4in1 ESC with 30.5x30.5 mm Mounting holes, supports DSHOT 1200, BLHELI32 firmware.
$59.99
Per Page      1 - 5 of 5
  • 1